Protect your spa cover from bumps and scrapes and make it easy to remove with this handy cover lifter!
This lifter requires:
This cover lifter requires the thickness of your spa cover plus approximately 100mm for operational clearance.
We recommend at least 600mm, if less than this the cover will touch any surface nearer to the spa.
Important notes:
The manufacturer installation instructions state that you will need 26" (660mm) for installations. This is not the operational clearance. We have installed these with less than 660mm of clearance. Approximately 200mm of the lifters foot protrudes from the base of the spa once it is installed. In low clearance situations, the foot can be slid in from the side of the spa which allows installation with less than 660mm (26 inches).
If you are uncertain if you have adequate clearance please call or chat with us.
In most instances, you will need to empty your spa in order to install this lifter because the feet slide under the spa. We have installed these on full spas by using a wedge to make room for the cover foot, however, depending on the spa model this can damage the base.
If you are installing a cover lifter on your swim spa, you will be required to fence around the area containing the steps and the cover lifter. (except NSW where fencing may not be required). If you have received advice that you only need to fence around your steps, this does not apply when a cover lifter is installed on your swim spa.
Portable spas require fencing around the entire spa in all states except NSW, regardless of whether a cover lifter is installed.
Please check with your local authorities for current regulations.
Need assistance with certification? Contact our compliance team for assistance.
This product is subject to Equipotential Bonding compliance in accordance with the Australian and New Zealand Standards (AS/NZS 3000: 2018 Electrical Installations) otherwise known as the Wiring Rules.
If this product is installed within 1.25m of a body of water including spa, swim spa or pool, then Equipotential Bonding MUST be performed by a licensed electrical person prior to the product being used. This is a mandatory requirement. As the purchaser of this product, you are responsible for ensuring compliance with this requirement at your own expense.
Refer to the guide below for more information.
SKU | 759770 |
Model # | 759770 |
Barcode # | 9352861009090 |
Brand | Spa World™ |
Shipping Weight | 8.0000kg |
Shipping Width | 1.160m |
Shipping Height | 0.200m |
Shipping Length | 0.240m |
Shipping Cubic | 0.055680000m3 |
Unit Of Measure | ea |
Protect your spa cover from bumps and scrapes and make it easy to remove with this handy cover lifter!
This lifter requires:
This cover lifter requires the thickness of your spa cover plus approximately 100mm for operational clearance.
We recommend at least 600mm, if less than this the cover will touch any surface nearer to the spa.
Important notes:
The manufacturer installation instructions state that you will need 26" (660mm) for installations. This is not the operational clearance. We have installed these with less than 660mm of clearance. Approximately 200mm of the lifters foot protrudes from the base of the spa once it is installed. In low clearance situations, the foot can be slid in from the side of the spa which allows installation with less than 660mm (26 inches).
If you are uncertain if you have adequate clearance please call or chat with us.
In most instances, you will need to empty your spa in order to install this lifter because the feet slide under the spa. We have installed these on full spas by using a wedge to make room for the cover foot, however, depending on the spa model this can damage the base.
If you are installing a cover lifter on your swim spa, you will be required to fence around the area containing the steps and the cover lifter. (except NSW where fencing may not be required). If you have received advice that you only need to fence around your steps, this does not apply when a cover lifter is installed on your swim spa.
Portable spas require fencing around the entire spa in all states except NSW, regardless of whether a cover lifter is installed.
Please check with your local authorities for current regulations.
Need assistance with certification? Contact our compliance team for assistance.
This product is subject to Equipotential Bonding compliance in accordance with the Australian and New Zealand Standards (AS/NZS 3000: 2018 Electrical Installations) otherwise known as the Wiring Rules.
If this product is installed within 1.25m of a body of water including spa, swim spa or pool, then Equipotential Bonding MUST be performed by a licensed electrical person prior to the product being used. This is a mandatory requirement. As the purchaser of this product, you are responsible for ensuring compliance with this requirement at your own expense.
Refer to the guide below for more information.
SKU | 759770 |
Model # | 759770 |
Barcode # | 9352861009090 |
Brand | Spa World™ |
Shipping Weight | 8.0000kg |
Shipping Width | 1.160m |
Shipping Height | 0.200m |
Shipping Length | 0.240m |
Shipping Cubic | 0.055680000m3 |
Unit Of Measure | ea |
Protect your spa cover from bumps and scrapes and make it easy to remove with this handy cover lifter!
This lifter requires:
This cover lifter requires the thickness of your spa cover plus approximately 100mm for operational clearance.
We recommend at least 600mm, if less than this the cover will touch any surface nearer to the spa.
Important notes:
The manufacturer installation instructions state that you will need 26" (660mm) for installations. This is not the operational clearance. We have installed these with less than 660mm of clearance. Approximately 200mm of the lifters foot protrudes from the base of the spa once it is installed. In low clearance situations, the foot can be slid in from the side of the spa which allows installation with less than 660mm (26 inches).
If you are uncertain if you have adequate clearance please call or chat with us.
In most instances, you will need to empty your spa in order to install this lifter because the feet slide under the spa. We have installed these on full spas by using a wedge to make room for the cover foot, however, depending on the spa model this can damage the base.
If you are installing a cover lifter on your swim spa, you will be required to fence around the area containing the steps and the cover lifter. (except NSW where fencing may not be required). If you have received advice that you only need to fence around your steps, this does not apply when a cover lifter is installed on your swim spa.
Portable spas require fencing around the entire spa in all states except NSW, regardless of whether a cover lifter is installed.
Please check with your local authorities for current regulations.
Need assistance with certification? Contact our compliance team for assistance.
This product is subject to Equipotential Bonding compliance in accordance with the Australian and New Zealand Standards (AS/NZS 3000: 2018 Electrical Installations) otherwise known as the Wiring Rules.
If this product is installed within 1.25m of a body of water including spa, swim spa or pool, then Equipotential Bonding MUST be performed by a licensed electrical person prior to the product being used. This is a mandatory requirement. As the purchaser of this product, you are responsible for ensuring compliance with this requirement at your own expense.
Refer to the guide below for more information.
SKU | 759770 |
Model # | 759770 |
Barcode # | 9352861009090 |
Brand | Spa World™ |
Shipping Weight | 8.0000kg |
Shipping Width | 1.160m |
Shipping Height | 0.200m |
Shipping Length | 0.240m |
Shipping Cubic | 0.055680000m3 |
Unit Of Measure | ea |
We are proud that Spa World customers have given us a Five Star Trustpilot rating.
For peace of mind
With a Spa Store Account
on AU orders over $199*
With 7-day online chat support